Understanding Dose Area Product and Air Kerma

Dose Area Product (DAP) and Air Kerma (AK) are measurements commonly used to represent the dose your patient receives during an X-ray procedure. What the terms mean is often not well understood. What actions can be taken to reduce the numbers is important to review.

Kontaktinė informacija

* Šis laukelis yra privalomas

Šalis

Kontaktiniai duomenys

Vardas*

Vardas (Fonetinis)

Pavardė*

Pavardė (Fonetinis)

Pasveikinimas

Akademinis pavadinimas

El. pašto adresas*

Telefonas

Įmonės rekvizitai

Pareigos*

Pareigos

Industrija

Funkcija

Specialybė

Departamentas

Valstija / provincija

Miestas

Adresas

Pašto indeksas / pašto kodas

Verslo informacija

Nurodydami priežastis susisiekti, mes galime suteikti jums geresnę paslaugą.

Tolesnė informacija

Pageidautinas kontaktinis būdas

Geriausias laikas skambinti

Numatytas įsigijimo laikas

Komentarai

What is cross border data transfer?

I agree on cross-border transfer of personal information.

I would like to receive marketing related electronic communications about Philips products, services, events and promotions that may be relevant to me based on my user preferences and behaviour.

How do DAP and AK differ?

Consider the analogy of the garden hose spraying water through a window, where the hose is the X-ray tube, the water represents radiation from the X-ray tube, and the window is the collimator. Water only passes through the open part of the window.

What is Dose Area Product?

Dose Area Product (DAP) is an output measurement of the total amount of radiation delivered to the patient. Think of it as the total amount (volume) of water coming through the window. The amount is the same regardless of whether it is measured close to the hose (3) or further away (4). Only the area measured changes (grows broader) further from the hose.

What is Air Kerma?

Air Kerma (AK) is a dose (rate) measurement of radiation at a specific defined position such as a point on the patient’s skin. Think of it as the amount of water from the hose hitting a one square centimeter cup (1cm2). If the cup is close to the hose (5) it will fill quickly (a high AK measurement). If it is farther away (6) it will fill slowly (a low AK measurement).

X-ray tube

Collimator

DAP chambers

AK dose meters

Note: A “DAP chamber” is a dose meter but it measures all radiation passing through it rather than sampling 1cm²Air Kerma is the measurement of the dose the patient’s skin recieves and Dose Area Product is a measurement of all dose exposure.

What do the numbers tell us?

DAP measurement provides a general dose reference and guideline for risk, but does not tell how much dose was received by the patient in a particular spot. AK is very accurate for dose measured at a particular spot (i.e. the reference point – 15cm towards the tube from the isocenter) and in 10 different projections using Philips Zone Dose Reporting, but does not offer a picture of overall radiation dose. DAP and AK compliment each other. DAP and AK readouts taken during the procedure can be used to help minimize radiation. System operation plays an extremely important role. How was dose applied? How was it distributed? You have control.

Radiation exposure readouts
with Zone Reporting

During radiation - DoseRate per second or minute

DAP	56 mGycm 2/S
1.9 min Time	61.709 mGy/min AK

Enable dose management across your organization

DoseWise Portal is a vendor-agnostic, web-based solution that collects, measures, analyzes, and reports patient & staff radiation exposure, assisting you to take control of quality of care, efficiency, and patient/staff safety.

View product

What you can do to manage patient dose

Limit fluoro and exposure time Select the lowest ‘acceptable’ image quality dose setting for fluoro and exposure if available.

Keep source to image distance (SID) down. An increase of just 20cm results in a 60%+ increase in AK dose to the patient.

Collimate whenever possible. If you don’t need to see it, don’t radiate it. Collimation greatly reduces DAP and scatter radiation too.

Increase Field of View (FOV) and collimate. You must to both. If you just increase FOV, AK goes down, but DAP goes up.

Do not lower table below isocenter if not necessary. Also, minimize angles — steeper angles put the X-ray tube closer to the patient, increasing AK.

Always keep detector as close to the patient as possible. Dose is increased as the detector moves away to maintain image quality.

If you can’t reduce it — move it! Radiation injury can be avoided. Do whatever is needed to change the entrance point on the patient.